Filtered by CWE-667
Filtered by vendor Subscriptions
Total 516 CVE
CVE Vendors Products Updated CVSS v3.1
CVE-2023-52583 2 Debian, Linux 2 Debian Linux, Linux Kernel 2025-05-04 5.5 Medium
In the Linux kernel, the following vulnerability has been resolved: ceph: fix deadlock or deadcode of misusing dget() The lock order is incorrect between denty and its parent, we should always make sure that the parent get the lock first. But since this deadcode is never used and the parent dir will always be set from the callers, let's just remove it.
CVE-2023-52516 1 Linux 1 Linux Kernel 2025-05-04 5.5 Medium
In the Linux kernel, the following vulnerability has been resolved: dma-debug: don't call __dma_entry_alloc_check_leak() under free_entries_lock __dma_entry_alloc_check_leak() calls into printk -> serial console output (qcom geni) and grabs port->lock under free_entries_lock spin lock, which is a reverse locking dependency chain as qcom_geni IRQ handler can call into dma-debug code and grab free_entries_lock under port->lock. Move __dma_entry_alloc_check_leak() call out of free_entries_lock scope so that we don't acquire serial console's port->lock under it. Trimmed-down lockdep splat: The existing dependency chain (in reverse order) is: -> #2 (free_entries_lock){-.-.}-{2:2}: _raw_spin_lock_irqsave+0x60/0x80 dma_entry_alloc+0x38/0x110 debug_dma_map_page+0x60/0xf8 dma_map_page_attrs+0x1e0/0x230 dma_map_single_attrs.constprop.0+0x6c/0xc8 geni_se_rx_dma_prep+0x40/0xcc qcom_geni_serial_isr+0x310/0x510 __handle_irq_event_percpu+0x110/0x244 handle_irq_event_percpu+0x20/0x54 handle_irq_event+0x50/0x88 handle_fasteoi_irq+0xa4/0xcc handle_irq_desc+0x28/0x40 generic_handle_domain_irq+0x24/0x30 gic_handle_irq+0xc4/0x148 do_interrupt_handler+0xa4/0xb0 el1_interrupt+0x34/0x64 el1h_64_irq_handler+0x18/0x24 el1h_64_irq+0x64/0x68 arch_local_irq_enable+0x4/0x8 ____do_softirq+0x18/0x24 ... -> #1 (&port_lock_key){-.-.}-{2:2}: _raw_spin_lock_irqsave+0x60/0x80 qcom_geni_serial_console_write+0x184/0x1dc console_flush_all+0x344/0x454 console_unlock+0x94/0xf0 vprintk_emit+0x238/0x24c vprintk_default+0x3c/0x48 vprintk+0xb4/0xbc _printk+0x68/0x90 register_console+0x230/0x38c uart_add_one_port+0x338/0x494 qcom_geni_serial_probe+0x390/0x424 platform_probe+0x70/0xc0 really_probe+0x148/0x280 __driver_probe_device+0xfc/0x114 driver_probe_device+0x44/0x100 __device_attach_driver+0x64/0xdc bus_for_each_drv+0xb0/0xd8 __device_attach+0xe4/0x140 device_initial_probe+0x1c/0x28 bus_probe_device+0x44/0xb0 device_add+0x538/0x668 of_device_add+0x44/0x50 of_platform_device_create_pdata+0x94/0xc8 of_platform_bus_create+0x270/0x304 of_platform_populate+0xac/0xc4 devm_of_platform_populate+0x60/0xac geni_se_probe+0x154/0x160 platform_probe+0x70/0xc0 ... -> #0 (console_owner){-...}-{0:0}: __lock_acquire+0xdf8/0x109c lock_acquire+0x234/0x284 console_flush_all+0x330/0x454 console_unlock+0x94/0xf0 vprintk_emit+0x238/0x24c vprintk_default+0x3c/0x48 vprintk+0xb4/0xbc _printk+0x68/0x90 dma_entry_alloc+0xb4/0x110 debug_dma_map_sg+0xdc/0x2f8 __dma_map_sg_attrs+0xac/0xe4 dma_map_sgtable+0x30/0x4c get_pages+0x1d4/0x1e4 [msm] msm_gem_pin_pages_locked+0x38/0xac [msm] msm_gem_pin_vma_locked+0x58/0x88 [msm] msm_ioctl_gem_submit+0xde4/0x13ac [msm] drm_ioctl_kernel+0xe0/0x15c drm_ioctl+0x2e8/0x3f4 vfs_ioctl+0x30/0x50 ... Chain exists of: console_owner --> &port_lock_key --> free_entries_lock Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(free_entries_lock); lock(&port_lock_key); lock(free_entries_lock); lock(console_owner); *** DEADLOCK *** Call trace: dump_backtrace+0xb4/0xf0 show_stack+0x20/0x30 dump_stack_lvl+0x60/0x84 dump_stack+0x18/0x24 print_circular_bug+0x1cc/0x234 check_noncircular+0x78/0xac __lock_acquire+0xdf8/0x109c lock_acquire+0x234/0x284 console_flush_all+0x330/0x454 consol ---truncated---
CVE-2023-52505 1 Linux 1 Linux Kernel 2025-05-04 4.7 Medium
In the Linux kernel, the following vulnerability has been resolved: phy: lynx-28g: serialize concurrent phy_set_mode_ext() calls to shared registers The protocol converter configuration registers PCC8, PCCC, PCCD (implemented by the driver), as well as others, control protocol converters from multiple lanes (each represented as a different struct phy). So, if there are simultaneous calls to phy_set_mode_ext() to lanes sharing the same PCC register (either for the "old" or for the "new" protocol), corruption of the values programmed to hardware is possible, because lynx_28g_rmw() has no locking. Add a spinlock in the struct lynx_28g_priv shared by all lanes, and take the global spinlock from the phy_ops :: set_mode() implementation. There are no other callers which modify PCC registers.
CVE-2023-52498 2 Linux, Redhat 2 Linux Kernel, Enterprise Linux 2025-05-04 5.5 Medium
In the Linux kernel, the following vulnerability has been resolved: PM: sleep: Fix possible deadlocks in core system-wide PM code It is reported that in low-memory situations the system-wide resume core code deadlocks, because async_schedule_dev() executes its argument function synchronously if it cannot allocate memory (and not only in that case) and that function attempts to acquire a mutex that is already held. Executing the argument function synchronously from within dpm_async_fn() may also be problematic for ordering reasons (it may cause a consumer device's resume callback to be invoked before a requisite supplier device's one, for example). Address this by changing the code in question to use async_schedule_dev_nocall() for scheduling the asynchronous execution of device suspend and resume functions and to directly run them synchronously if async_schedule_dev_nocall() returns false.
CVE-2023-52493 1 Linux 1 Linux Kernel 2025-05-04 5.5 Medium
In the Linux kernel, the following vulnerability has been resolved: bus: mhi: host: Drop chan lock before queuing buffers Ensure read and write locks for the channel are not taken in succession by dropping the read lock from parse_xfer_event() such that a callback given to client can potentially queue buffers and acquire the write lock in that process. Any queueing of buffers should be done without channel read lock acquired as it can result in multiple locks and a soft lockup. [mani: added fixes tag and cc'ed stable]
CVE-2023-52486 2 Linux, Redhat 6 Linux Kernel, Enterprise Linux, Rhel Aus and 3 more 2025-05-04 5.5 Medium
In the Linux kernel, the following vulnerability has been resolved: drm: Don't unref the same fb many times by mistake due to deadlock handling If we get a deadlock after the fb lookup in drm_mode_page_flip_ioctl() we proceed to unref the fb and then retry the whole thing from the top. But we forget to reset the fb pointer back to NULL, and so if we then get another error during the retry, before the fb lookup, we proceed the unref the same fb again without having gotten another reference. The end result is that the fb will (eventually) end up being freed while it's still in use. Reset fb to NULL once we've unreffed it to avoid doing it again until we've done another fb lookup. This turned out to be pretty easy to hit on a DG2 when doing async flips (and CONFIG_DEBUG_WW_MUTEX_SLOWPATH=y). The first symptom I saw that drm_closefb() simply got stuck in a busy loop while walking the framebuffer list. Fortunately I was able to convince it to oops instead, and from there it was easier to track down the culprit.
CVE-2023-52484 1 Linux 1 Linux Kernel 2025-05-04 5.5 Medium
In the Linux kernel, the following vulnerability has been resolved: iommu/arm-smmu-v3: Fix soft lockup triggered by arm_smmu_mm_invalidate_range When running an SVA case, the following soft lockup is triggered: -------------------------------------------------------------------- watchdog: BUG: soft lockup - CPU#244 stuck for 26s! pstate: 83400009 (Nzcv daif +PAN -UAO +TCO +DIT -SSBS BTYPE=--) pc : arm_smmu_cmdq_issue_cmdlist+0x178/0xa50 lr : arm_smmu_cmdq_issue_cmdlist+0x150/0xa50 sp : ffff8000d83ef290 x29: ffff8000d83ef290 x28: 000000003b9aca00 x27: 0000000000000000 x26: ffff8000d83ef3c0 x25: da86c0812194a0e8 x24: 0000000000000000 x23: 0000000000000040 x22: ffff8000d83ef340 x21: ffff0000c63980c0 x20: 0000000000000001 x19: ffff0000c6398080 x18: 0000000000000000 x17: 0000000000000000 x16: 0000000000000000 x15: ffff3000b4a3bbb0 x14: ffff3000b4a30888 x13: ffff3000b4a3cf60 x12: 0000000000000000 x11: 0000000000000000 x10: 0000000000000000 x9 : ffffc08120e4d6bc x8 : 0000000000000000 x7 : 0000000000000000 x6 : 0000000000048cfa x5 : 0000000000000000 x4 : 0000000000000001 x3 : 000000000000000a x2 : 0000000080000000 x1 : 0000000000000000 x0 : 0000000000000001 Call trace: arm_smmu_cmdq_issue_cmdlist+0x178/0xa50 __arm_smmu_tlb_inv_range+0x118/0x254 arm_smmu_tlb_inv_range_asid+0x6c/0x130 arm_smmu_mm_invalidate_range+0xa0/0xa4 __mmu_notifier_invalidate_range_end+0x88/0x120 unmap_vmas+0x194/0x1e0 unmap_region+0xb4/0x144 do_mas_align_munmap+0x290/0x490 do_mas_munmap+0xbc/0x124 __vm_munmap+0xa8/0x19c __arm64_sys_munmap+0x28/0x50 invoke_syscall+0x78/0x11c el0_svc_common.constprop.0+0x58/0x1c0 do_el0_svc+0x34/0x60 el0_svc+0x2c/0xd4 el0t_64_sync_handler+0x114/0x140 el0t_64_sync+0x1a4/0x1a8 -------------------------------------------------------------------- Note that since 6.6-rc1 the arm_smmu_mm_invalidate_range above is renamed to "arm_smmu_mm_arch_invalidate_secondary_tlbs", yet the problem remains. The commit 06ff87bae8d3 ("arm64: mm: remove unused functions and variable protoypes") fixed a similar lockup on the CPU MMU side. Yet, it can occur to SMMU too, since arm_smmu_mm_arch_invalidate_secondary_tlbs() is called typically next to MMU tlb flush function, e.g. tlb_flush_mmu_tlbonly { tlb_flush { __flush_tlb_range { // check MAX_TLBI_OPS } } mmu_notifier_arch_invalidate_secondary_tlbs { arm_smmu_mm_arch_invalidate_secondary_tlbs { // does not check MAX_TLBI_OPS } } } Clone a CMDQ_MAX_TLBI_OPS from the MAX_TLBI_OPS in tlbflush.h, since in an SVA case SMMU uses the CPU page table, so it makes sense to align with the tlbflush code. Then, replace per-page TLBI commands with a single per-asid TLBI command, if the request size hits this threshold.
CVE-2023-52456 1 Linux 1 Linux Kernel 2025-05-04 5.5 Medium
In the Linux kernel, the following vulnerability has been resolved: serial: imx: fix tx statemachine deadlock When using the serial port as RS485 port, the tx statemachine is used to control the RTS pin to drive the RS485 transceiver TX_EN pin. When the TTY port is closed in the middle of a transmission (for instance during userland application crash), imx_uart_shutdown disables the interface and disables the Transmission Complete interrupt. afer that, imx_uart_stop_tx bails on an incomplete transmission, to be retriggered by the TC interrupt. This interrupt is disabled and therefore the tx statemachine never transitions out of SEND. The statemachine is in deadlock now, and the TX_EN remains low, making the interface useless. imx_uart_stop_tx now checks for incomplete transmission AND whether TC interrupts are enabled before bailing to be retriggered. This makes sure the state machine handling is reached, and is properly set to WAIT_AFTER_SEND.
CVE-2025-22014 1 Linux 1 Linux Kernel 2025-05-04 5.5 Medium
In the Linux kernel, the following vulnerability has been resolved: soc: qcom: pdr: Fix the potential deadlock When some client process A call pdr_add_lookup() to add the look up for the service and does schedule locator work, later a process B got a new server packet indicating locator is up and call pdr_locator_new_server() which eventually sets pdr->locator_init_complete to true which process A sees and takes list lock and queries domain list but it will timeout due to deadlock as the response will queued to the same qmi->wq and it is ordered workqueue and process B is not able to complete new server request work due to deadlock on list lock. Fix it by removing the unnecessary list iteration as the list iteration is already being done inside locator work, so avoid it here and just call schedule_work() here. Process A Process B process_scheduled_works() pdr_add_lookup() qmi_data_ready_work() process_scheduled_works() pdr_locator_new_server() pdr->locator_init_complete=true; pdr_locator_work() mutex_lock(&pdr->list_lock); pdr_locate_service() mutex_lock(&pdr->list_lock); pdr_get_domain_list() pr_err("PDR: %s get domain list txn wait failed: %d\n", req->service_name, ret); Timeout error log due to deadlock: " PDR: tms/servreg get domain list txn wait failed: -110 PDR: service lookup for msm/adsp/sensor_pd:tms/servreg failed: -110 " Thanks to Bjorn and Johan for letting me know that this commit also fixes an audio regression when using the in-kernel pd-mapper as that makes it easier to hit this race. [1]
CVE-2025-22012 1 Linux 1 Linux Kernel 2025-05-04 5.5 Medium
In the Linux kernel, the following vulnerability has been resolved: Revert "arm64: dts: qcom: sdm845: Affirm IDR0.CCTW on apps_smmu" There are reports that the pagetable walker cache coherency is not a given across the spectrum of SDM845/850 devices, leading to lock-ups and resets. It works fine on some devices (like the Dragonboard 845c, but not so much on the Lenovo Yoga C630). This unfortunately looks like a fluke in firmware development, where likely somewhere in the vast hypervisor stack, a change to accommodate for this was only introduced after the initial software release (which often serves as a baseline for products). Revert the change to avoid additional guesswork around crashes. This reverts commit 6b31a9744b8726c69bb0af290f8475a368a4b805.
CVE-2025-22010 1 Linux 1 Linux Kernel 2025-05-04 5.5 Medium
In the Linux kernel, the following vulnerability has been resolved: RDMA/hns: Fix soft lockup during bt pages loop Driver runs a for-loop when allocating bt pages and mapping them with buffer pages. When a large buffer (e.g. MR over 100GB) is being allocated, it may require a considerable loop count. This will lead to soft lockup: watchdog: BUG: soft lockup - CPU#27 stuck for 22s! ... Call trace: hem_list_alloc_mid_bt+0x124/0x394 [hns_roce_hw_v2] hns_roce_hem_list_request+0xf8/0x160 [hns_roce_hw_v2] hns_roce_mtr_create+0x2e4/0x360 [hns_roce_hw_v2] alloc_mr_pbl+0xd4/0x17c [hns_roce_hw_v2] hns_roce_reg_user_mr+0xf8/0x190 [hns_roce_hw_v2] ib_uverbs_reg_mr+0x118/0x290 watchdog: BUG: soft lockup - CPU#35 stuck for 23s! ... Call trace: hns_roce_hem_list_find_mtt+0x7c/0xb0 [hns_roce_hw_v2] mtr_map_bufs+0xc4/0x204 [hns_roce_hw_v2] hns_roce_mtr_create+0x31c/0x3c4 [hns_roce_hw_v2] alloc_mr_pbl+0xb0/0x160 [hns_roce_hw_v2] hns_roce_reg_user_mr+0x108/0x1c0 [hns_roce_hw_v2] ib_uverbs_reg_mr+0x120/0x2bc Add a cond_resched() to fix soft lockup during these loops. In order not to affect the allocation performance of normal-size buffer, set the loop count of a 100GB MR as the threshold to call cond_resched().
CVE-2025-21951 1 Linux 1 Linux Kernel 2025-05-04 5.5 Medium
In the Linux kernel, the following vulnerability has been resolved: bus: mhi: host: pci_generic: Use pci_try_reset_function() to avoid deadlock There are multiple places from where the recovery work gets scheduled asynchronously. Also, there are multiple places where the caller waits synchronously for the recovery to be completed. One such place is during the PM shutdown() callback. If the device is not alive during recovery_work, it will try to reset the device using pci_reset_function(). This function internally will take the device_lock() first before resetting the device. By this time, if the lock has already been acquired, then recovery_work will get stalled while waiting for the lock. And if the lock was already acquired by the caller which waits for the recovery_work to be completed, it will lead to deadlock. This is what happened on the X1E80100 CRD device when the device died before shutdown() callback. Driver core calls the driver's shutdown() callback while holding the device_lock() leading to deadlock. And this deadlock scenario can occur on other paths as well, like during the PM suspend() callback, where the driver core would hold the device_lock() before calling driver's suspend() callback. And if the recovery_work was already started, it could lead to deadlock. This is also observed on the X1E80100 CRD. So to fix both issues, use pci_try_reset_function() in recovery_work. This function first checks for the availability of the device_lock() before trying to reset the device. If the lock is available, it will acquire it and reset the device. Otherwise, it will return -EAGAIN. If that happens, recovery_work will fail with the error message "Recovery failed" as not much could be done.
CVE-2025-21939 2025-05-04 6.1 Medium
In the Linux kernel, the following vulnerability has been resolved: drm/xe/hmm: Don't dereference struct page pointers without notifier lock The pnfs that we obtain from hmm_range_fault() point to pages that we don't have a reference on, and the guarantee that they are still in the cpu page-tables is that the notifier lock must be held and the notifier seqno is still valid. So while building the sg table and marking the pages accesses / dirty we need to hold this lock with a validated seqno. However, the lock is reclaim tainted which makes sg_alloc_table_from_pages_segment() unusable, since it internally allocates memory. Instead build the sg-table manually. For the non-iommu case this might lead to fewer coalesces, but if that's a problem it can be fixed up later in the resource cursor code. For the iommu case, the whole sg-table may still be coalesced to a single contigous device va region. This avoids marking pages that we don't own dirty and accessed, and it also avoid dereferencing struct pages that we don't own. v2: - Use assert to check whether hmm pfns are valid (Matthew Auld) - Take into account that large pages may cross range boundaries (Matthew Auld) v3: - Don't unnecessarily check for a non-freed sg-table. (Matthew Auld) - Add a missing up_read() in an error path. (Matthew Auld) (cherry picked from commit ea3e66d280ce2576664a862693d1da8fd324c317)
CVE-2025-21912 1 Linux 1 Linux Kernel 2025-05-04 5.5 Medium
In the Linux kernel, the following vulnerability has been resolved: gpio: rcar: Use raw_spinlock to protect register access Use raw_spinlock in order to fix spurious messages about invalid context when spinlock debugging is enabled. The lock is only used to serialize register access. [ 4.239592] ============================= [ 4.239595] [ BUG: Invalid wait context ] [ 4.239599] 6.13.0-rc7-arm64-renesas-05496-gd088502a519f #35 Not tainted [ 4.239603] ----------------------------- [ 4.239606] kworker/u8:5/76 is trying to lock: [ 4.239609] ffff0000091898a0 (&p->lock){....}-{3:3}, at: gpio_rcar_config_interrupt_input_mode+0x34/0x164 [ 4.239641] other info that might help us debug this: [ 4.239643] context-{5:5} [ 4.239646] 5 locks held by kworker/u8:5/76: [ 4.239651] #0: ffff0000080fb148 ((wq_completion)async){+.+.}-{0:0}, at: process_one_work+0x190/0x62c [ 4.250180] OF: /soc/sound@ec500000/ports/port@0/endpoint: Read of boolean property 'frame-master' with a value. [ 4.254094] #1: ffff80008299bd80 ((work_completion)(&entry->work)){+.+.}-{0:0}, at: process_one_work+0x1b8/0x62c [ 4.254109] #2: ffff00000920c8f8 [ 4.258345] OF: /soc/sound@ec500000/ports/port@1/endpoint: Read of boolean property 'bitclock-master' with a value. [ 4.264803] (&dev->mutex){....}-{4:4}, at: __device_attach_async_helper+0x3c/0xdc [ 4.264820] #3: ffff00000a50ca40 (request_class#2){+.+.}-{4:4}, at: __setup_irq+0xa0/0x690 [ 4.264840] #4: [ 4.268872] OF: /soc/sound@ec500000/ports/port@1/endpoint: Read of boolean property 'frame-master' with a value. [ 4.273275] ffff00000a50c8c8 (lock_class){....}-{2:2}, at: __setup_irq+0xc4/0x690 [ 4.296130] renesas_sdhi_internal_dmac ee100000.mmc: mmc1 base at 0x00000000ee100000, max clock rate 200 MHz [ 4.304082] stack backtrace: [ 4.304086] CPU: 1 UID: 0 PID: 76 Comm: kworker/u8:5 Not tainted 6.13.0-rc7-arm64-renesas-05496-gd088502a519f #35 [ 4.304092] Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) [ 4.304097] Workqueue: async async_run_entry_fn [ 4.304106] Call trace: [ 4.304110] show_stack+0x14/0x20 (C) [ 4.304122] dump_stack_lvl+0x6c/0x90 [ 4.304131] dump_stack+0x14/0x1c [ 4.304138] __lock_acquire+0xdfc/0x1584 [ 4.426274] lock_acquire+0x1c4/0x33c [ 4.429942] _raw_spin_lock_irqsave+0x5c/0x80 [ 4.434307] gpio_rcar_config_interrupt_input_mode+0x34/0x164 [ 4.440061] gpio_rcar_irq_set_type+0xd4/0xd8 [ 4.444422] __irq_set_trigger+0x5c/0x178 [ 4.448435] __setup_irq+0x2e4/0x690 [ 4.452012] request_threaded_irq+0xc4/0x190 [ 4.456285] devm_request_threaded_irq+0x7c/0xf4 [ 4.459398] ata1: link resume succeeded after 1 retries [ 4.460902] mmc_gpiod_request_cd_irq+0x68/0xe0 [ 4.470660] mmc_start_host+0x50/0xac [ 4.474327] mmc_add_host+0x80/0xe4 [ 4.477817] tmio_mmc_host_probe+0x2b0/0x440 [ 4.482094] renesas_sdhi_probe+0x488/0x6f4 [ 4.486281] renesas_sdhi_internal_dmac_probe+0x60/0x78 [ 4.491509] platform_probe+0x64/0xd8 [ 4.495178] really_probe+0xb8/0x2a8 [ 4.498756] __driver_probe_device+0x74/0x118 [ 4.503116] driver_probe_device+0x3c/0x154 [ 4.507303] __device_attach_driver+0xd4/0x160 [ 4.511750] bus_for_each_drv+0x84/0xe0 [ 4.515588] __device_attach_async_helper+0xb0/0xdc [ 4.520470] async_run_entry_fn+0x30/0xd8 [ 4.524481] process_one_work+0x210/0x62c [ 4.528494] worker_thread+0x1ac/0x340 [ 4.532245] kthread+0x10c/0x110 [ 4.535476] ret_from_fork+0x10/0x20
CVE-2025-21911 1 Linux 1 Linux Kernel 2025-05-04 5.5 Medium
In the Linux kernel, the following vulnerability has been resolved: drm/imagination: avoid deadlock on fence release Do scheduler queue fence release processing on a workqueue, rather than in the release function itself. Fixes deadlock issues such as the following: [ 607.400437] ============================================ [ 607.405755] WARNING: possible recursive locking detected [ 607.415500] -------------------------------------------- [ 607.420817] weston:zfq0/24149 is trying to acquire lock: [ 607.426131] ffff000017d041a0 (reservation_ww_class_mutex){+.+.}-{3:3}, at: pvr_gem_object_vunmap+0x40/0xc0 [powervr] [ 607.436728] but task is already holding lock: [ 607.442554] ffff000017d105a0 (reservation_ww_class_mutex){+.+.}-{3:3}, at: dma_buf_ioctl+0x250/0x554 [ 607.451727] other info that might help us debug this: [ 607.458245] Possible unsafe locking scenario: [ 607.464155] CPU0 [ 607.466601] ---- [ 607.469044] lock(reservation_ww_class_mutex); [ 607.473584] lock(reservation_ww_class_mutex); [ 607.478114] *** DEADLOCK ***
CVE-2025-21908 1 Linux 1 Linux Kernel 2025-05-04 5.5 Medium
In the Linux kernel, the following vulnerability has been resolved: NFS: fix nfs_release_folio() to not deadlock via kcompactd writeback Add PF_KCOMPACTD flag and current_is_kcompactd() helper to check for it so nfs_release_folio() can skip calling nfs_wb_folio() from kcompactd. Otherwise NFS can deadlock waiting for kcompactd enduced writeback which recurses back to NFS (which triggers writeback to NFSD via NFS loopback mount on the same host, NFSD blocks waiting for XFS's call to __filemap_get_folio): 6070.550357] INFO: task kcompactd0:58 blocked for more than 4435 seconds. {--- [58] "kcompactd0" [<0>] folio_wait_bit+0xe8/0x200 [<0>] folio_wait_writeback+0x2b/0x80 [<0>] nfs_wb_folio+0x80/0x1b0 [nfs] [<0>] nfs_release_folio+0x68/0x130 [nfs] [<0>] split_huge_page_to_list_to_order+0x362/0x840 [<0>] migrate_pages_batch+0x43d/0xb90 [<0>] migrate_pages_sync+0x9a/0x240 [<0>] migrate_pages+0x93c/0x9f0 [<0>] compact_zone+0x8e2/0x1030 [<0>] compact_node+0xdb/0x120 [<0>] kcompactd+0x121/0x2e0 [<0>] kthread+0xcf/0x100 [<0>] ret_from_fork+0x31/0x40 [<0>] ret_from_fork_asm+0x1a/0x30 ---} [akpm@linux-foundation.org: fix build]
CVE-2025-21900 1 Linux 1 Linux Kernel 2025-05-04 5.5 Medium
In the Linux kernel, the following vulnerability has been resolved: NFSv4: Fix a deadlock when recovering state on a sillyrenamed file If the file is sillyrenamed, and slated for delete on close, it is possible for a server reboot to triggeer an open reclaim, with can again race with the application call to close(). When that happens, the call to put_nfs_open_context() can trigger a synchronous delegreturn call which deadlocks because it is not marked as privileged. Instead, ensure that the call to nfs4_inode_return_delegation_on_close() catches the delegreturn, and schedules it asynchronously.
CVE-2025-21871 2025-05-04 5.5 Medium
In the Linux kernel, the following vulnerability has been resolved: tee: optee: Fix supplicant wait loop OP-TEE supplicant is a user-space daemon and it's possible for it be hung or crashed or killed in the middle of processing an OP-TEE RPC call. It becomes more complicated when there is incorrect shutdown ordering of the supplicant process vs the OP-TEE client application which can eventually lead to system hang-up waiting for the closure of the client application. Allow the client process waiting in kernel for supplicant response to be killed rather than indefinitely waiting in an unkillable state. Also, a normal uninterruptible wait should not have resulted in the hung-task watchdog getting triggered, but the endless loop would. This fixes issues observed during system reboot/shutdown when supplicant got hung for some reason or gets crashed/killed which lead to client getting hung in an unkillable state. It in turn lead to system being in hung up state requiring hard power off/on to recover.
CVE-2025-21859 1 Linux 1 Linux Kernel 2025-05-04 5.5 Medium
In the Linux kernel, the following vulnerability has been resolved: USB: gadget: f_midi: f_midi_complete to call queue_work When using USB MIDI, a lock is attempted to be acquired twice through a re-entrant call to f_midi_transmit, causing a deadlock. Fix it by using queue_work() to schedule the inner f_midi_transmit() via a high priority work queue from the completion handler.
CVE-2025-21851 1 Linux 1 Linux Kernel 2025-05-04 3.3 Low
In the Linux kernel, the following vulnerability has been resolved: bpf: Fix softlockup in arena_map_free on 64k page kernel On an aarch64 kernel with CONFIG_PAGE_SIZE_64KB=y, arena_htab tests cause a segmentation fault and soft lockup. The same failure is not observed with 4k pages on aarch64. It turns out arena_map_free() is calling apply_to_existing_page_range() with the address returned by bpf_arena_get_kern_vm_start(). If this address is not page-aligned the code ends up calling apply_to_pte_range() with that unaligned address causing soft lockup. Fix it by round up GUARD_SZ to PAGE_SIZE << 1 so that the division by 2 in bpf_arena_get_kern_vm_start() returns a page-aligned value.