ReportizFlow
Filtered by vendor Linux
Subscriptions
Filtered by product Linux Kernel
Subscriptions
Total
18504 CVE
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2023-54026 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: opp: Fix use-after-free in lazy_opp_tables after probe deferral When dev_pm_opp_of_find_icc_paths() in _allocate_opp_table() returns -EPROBE_DEFER, the opp_table is freed again, to wait until all the interconnect paths are available. However, if the OPP table is using required-opps then it may already have been added to the global lazy_opp_tables list. The error path does not remove the opp_table from the list again. This can cause crashes later when the provider of the required-opps is added, since we will iterate over OPP tables that have already been freed. E.g.: Unable to handle kernel NULL pointer dereference when read CPU: 0 PID: 7 Comm: kworker/0:0 Not tainted 6.4.0-rc3 PC is at _of_add_opp_table_v2 (include/linux/of.h:949 drivers/opp/of.c:98 drivers/opp/of.c:344 drivers/opp/of.c:404 drivers/opp/of.c:1032) -> lazy_link_required_opp_table() Fix this by calling _of_clear_opp_table() to remove the opp_table from the list and clear other allocated resources. While at it, also add the missing mutex_destroy() calls in the error path. | ||||
| CVE-2022-50714 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7921e: fix rmmod crash in driver reload test In insmod/rmmod stress test, the following crash dump shows up immediately. The problem is caused by missing mt76_dev in mt7921_pci_remove(). We should make sure the drvdata is ready before probe() finished. [168.862789] ================================================================== [168.862797] BUG: KASAN: user-memory-access in try_to_grab_pending+0x59/0x480 [168.862805] Write of size 8 at addr 0000000000006df0 by task rmmod/5361 [168.862812] CPU: 7 PID: 5361 Comm: rmmod Tainted: G OE 5.19.0-rc6 #1 [168.862816] Hardware name: Intel(R) Client Systems NUC8i7BEH/NUC8BEB, 05/04/2020 [168.862820] Call Trace: [168.862822] <TASK> [168.862825] dump_stack_lvl+0x49/0x63 [168.862832] print_report.cold+0x493/0x6b7 [168.862845] kasan_report+0xa7/0x120 [168.862857] kasan_check_range+0x163/0x200 [168.862861] __kasan_check_write+0x14/0x20 [168.862866] try_to_grab_pending+0x59/0x480 [168.862870] __cancel_work_timer+0xbb/0x340 [168.862898] cancel_work_sync+0x10/0x20 [168.862902] mt7921_pci_remove+0x61/0x1c0 [mt7921e] [168.862909] pci_device_remove+0xa3/0x1d0 [168.862914] device_remove+0xc4/0x170 [168.862920] device_release_driver_internal+0x163/0x300 [168.862925] driver_detach+0xc7/0x1a0 [168.862930] bus_remove_driver+0xeb/0x2d0 [168.862935] driver_unregister+0x71/0xb0 [168.862939] pci_unregister_driver+0x30/0x230 [168.862944] mt7921_pci_driver_exit+0x10/0x1b [mt7921e] [168.862949] __x64_sys_delete_module+0x2f9/0x4b0 [168.862968] do_syscall_64+0x38/0x90 [168.862973] entry_SYSCALL_64_after_hwframe+0x63/0xcd Test steps: 1. insmode 2. do not ifup 3. rmmod quickly (within 1 second) | ||||
| CVE-2022-50712 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: devlink: hold region lock when flushing snapshots Netdevsim triggers a splat on reload, when it destroys regions with snapshots pending: WARNING: CPU: 1 PID: 787 at net/core/devlink.c:6291 devlink_region_snapshot_del+0x12e/0x140 CPU: 1 PID: 787 Comm: devlink Not tainted 6.1.0-07460-g7ae9888d6e1c #580 RIP: 0010:devlink_region_snapshot_del+0x12e/0x140 Call Trace: <TASK> devl_region_destroy+0x70/0x140 nsim_dev_reload_down+0x2f/0x60 [netdevsim] devlink_reload+0x1f7/0x360 devlink_nl_cmd_reload+0x6ce/0x860 genl_family_rcv_msg_doit.isra.0+0x145/0x1c0 This is the locking assert in devlink_region_snapshot_del(), we're supposed to be holding the region->snapshot_lock here. | ||||
| CVE-2023-54126 | 1 Linux | 1 Linux Kernel | 2026-04-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: crypto: safexcel - Cleanup ring IRQ workqueues on load failure A failure loading the safexcel driver results in the following warning on boot, because the IRQ affinity has not been correctly cleaned up. Ensure we clean up the affinity and workqueues on a failure to load the driver. crypto-safexcel: probe of f2800000.crypto failed with error -2 ------------[ cut here ]------------ WARNING: CPU: 1 PID: 232 at kernel/irq/manage.c:1913 free_irq+0x300/0x340 Modules linked in: hwmon mdio_i2c crypto_safexcel(+) md5 sha256_generic libsha256 authenc libdes omap_rng rng_core nft_masq nft_nat nft_chain_nat nf_nat nft_ct nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables libcrc32c nfnetlink fuse autofs4 CPU: 1 PID: 232 Comm: systemd-udevd Tainted: G W 6.1.6-00002-g9d4898824677 #3 Hardware name: MikroTik RB5009 (DT) pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : free_irq+0x300/0x340 lr : free_irq+0x2e0/0x340 sp : ffff800008fa3890 x29: ffff800008fa3890 x28: 0000000000000000 x27: 0000000000000000 x26: ffff8000008e6dc0 x25: ffff000009034cac x24: ffff000009034d50 x23: 0000000000000000 x22: 000000000000004a x21: ffff0000093e0d80 x20: ffff000009034c00 x19: ffff00000615fc00 x18: 0000000000000000 x17: 0000000000000000 x16: 0000000000000000 x15: 000075f5c1584c5e x14: 0000000000000017 x13: 0000000000000000 x12: 0000000000000040 x11: ffff000000579b60 x10: ffff000000579b62 x9 : ffff800008bbe370 x8 : ffff000000579dd0 x7 : 0000000000000000 x6 : ffff000000579e18 x5 : ffff000000579da8 x4 : ffff800008ca0000 x3 : ffff800008ca0188 x2 : 0000000013033204 x1 : ffff000009034c00 x0 : ffff8000087eadf0 Call trace: free_irq+0x300/0x340 devm_irq_release+0x14/0x20 devres_release_all+0xa0/0x100 device_unbind_cleanup+0x14/0x60 really_probe+0x198/0x2d4 __driver_probe_device+0x74/0xdc driver_probe_device+0x3c/0x110 __driver_attach+0x8c/0x190 bus_for_each_dev+0x6c/0xc0 driver_attach+0x20/0x30 bus_add_driver+0x148/0x1fc driver_register+0x74/0x120 __platform_driver_register+0x24/0x30 safexcel_init+0x48/0x1000 [crypto_safexcel] do_one_initcall+0x4c/0x1b0 do_init_module+0x44/0x1cc load_module+0x1724/0x1be4 __do_sys_finit_module+0xbc/0x110 __arm64_sys_finit_module+0x1c/0x24 invoke_syscall+0x44/0x110 el0_svc_common.constprop.0+0xc0/0xe0 do_el0_svc+0x20/0x80 el0_svc+0x14/0x4c el0t_64_sync_handler+0xb0/0xb4 el0t_64_sync+0x148/0x14c ---[ end trace 0000000000000000 ]--- | ||||
| CVE-2023-54120 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: Bluetooth: Fix race condition in hidp_session_thread There is a potential race condition in hidp_session_thread that may lead to use-after-free. For instance, the timer is active while hidp_del_timer is called in hidp_session_thread(). After hidp_session_put, then 'session' will be freed, causing kernel panic when hidp_idle_timeout is running. The solution is to use del_timer_sync instead of del_timer. Here is the call trace: ? hidp_session_probe+0x780/0x780 call_timer_fn+0x2d/0x1e0 __run_timers.part.0+0x569/0x940 hidp_session_probe+0x780/0x780 call_timer_fn+0x1e0/0x1e0 ktime_get+0x5c/0xf0 lapic_next_deadline+0x2c/0x40 clockevents_program_event+0x205/0x320 run_timer_softirq+0xa9/0x1b0 __do_softirq+0x1b9/0x641 __irq_exit_rcu+0xdc/0x190 irq_exit_rcu+0xe/0x20 sysvec_apic_timer_interrupt+0xa1/0xc0 | ||||
| CVE-2022-50710 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: ice: set tx_tstamps when creating new Tx rings via ethtool When the user changes the number of queues via ethtool, the driver allocates new rings. This allocation did not initialize tx_tstamps. This results in the tx_tstamps field being zero (due to kcalloc allocation), and would result in a NULL pointer dereference when attempting a transmit timestamp on the new ring. | ||||
| CVE-2023-54045 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: audit: fix possible soft lockup in __audit_inode_child() Tracefs or debugfs maybe cause hundreds to thousands of PATH records, too many PATH records maybe cause soft lockup. For example: 1. CONFIG_KASAN=y && CONFIG_PREEMPTION=n 2. auditctl -a exit,always -S open -k key 3. sysctl -w kernel.watchdog_thresh=5 4. mkdir /sys/kernel/debug/tracing/instances/test There may be a soft lockup as follows: watchdog: BUG: soft lockup - CPU#45 stuck for 7s! [mkdir:15498] Kernel panic - not syncing: softlockup: hung tasks Call trace: dump_backtrace+0x0/0x30c show_stack+0x20/0x30 dump_stack+0x11c/0x174 panic+0x27c/0x494 watchdog_timer_fn+0x2bc/0x390 __run_hrtimer+0x148/0x4fc __hrtimer_run_queues+0x154/0x210 hrtimer_interrupt+0x2c4/0x760 arch_timer_handler_phys+0x48/0x60 handle_percpu_devid_irq+0xe0/0x340 __handle_domain_irq+0xbc/0x130 gic_handle_irq+0x78/0x460 el1_irq+0xb8/0x140 __audit_inode_child+0x240/0x7bc tracefs_create_file+0x1b8/0x2a0 trace_create_file+0x18/0x50 event_create_dir+0x204/0x30c __trace_add_new_event+0xac/0x100 event_trace_add_tracer+0xa0/0x130 trace_array_create_dir+0x60/0x140 trace_array_create+0x1e0/0x370 instance_mkdir+0x90/0xd0 tracefs_syscall_mkdir+0x68/0xa0 vfs_mkdir+0x21c/0x34c do_mkdirat+0x1b4/0x1d4 __arm64_sys_mkdirat+0x4c/0x60 el0_svc_common.constprop.0+0xa8/0x240 do_el0_svc+0x8c/0xc0 el0_svc+0x20/0x30 el0_sync_handler+0xb0/0xb4 el0_sync+0x160/0x180 Therefore, we add cond_resched() to __audit_inode_child() to fix it. | ||||
| CVE-2023-54046 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: crypto: essiv - Handle EBUSY correctly As it is essiv only handles the special return value of EINPROGERSS, which means that in all other cases it will free data related to the request. However, as the caller of essiv may specify MAY_BACKLOG, we also need to expect EBUSY and treat it in the same way. Otherwise backlogged requests will trigger a use-after-free. | ||||
| CVE-2022-50637 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: cpufreq: qcom-hw: Fix memory leak in qcom_cpufreq_hw_read_lut() If "cpu_dev" fails to get opp table in qcom_cpufreq_hw_read_lut(), the program will return, resulting in "table" resource is not released. | ||||
| CVE-2022-50638 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: ext4: fix bug_on in __es_tree_search caused by bad boot loader inode We got a issue as fllows: ================================================================== kernel BUG at fs/ext4/extents_status.c:203! invalid opcode: 0000 [#1] PREEMPT SMP CPU: 1 PID: 945 Comm: cat Not tainted 6.0.0-next-20221007-dirty #349 RIP: 0010:ext4_es_end.isra.0+0x34/0x42 RSP: 0018:ffffc9000143b768 EFLAGS: 00010203 RAX: 0000000000000000 RBX: ffff8881769cd0b8 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffffffff8fc27cf7 RDI: 00000000ffffffff RBP: ffff8881769cd0bc R08: 0000000000000000 R09: ffffc9000143b5f8 R10: 0000000000000001 R11: 0000000000000001 R12: ffff8881769cd0a0 R13: ffff8881768e5668 R14: 00000000768e52f0 R15: 0000000000000000 FS: 00007f359f7f05c0(0000)GS:ffff88842fd00000(0000)knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f359f5a2000 CR3: 000000017130c000 CR4: 00000000000006e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> __es_tree_search.isra.0+0x6d/0xf5 ext4_es_cache_extent+0xfa/0x230 ext4_cache_extents+0xd2/0x110 ext4_find_extent+0x5d5/0x8c0 ext4_ext_map_blocks+0x9c/0x1d30 ext4_map_blocks+0x431/0xa50 ext4_mpage_readpages+0x48e/0xe40 ext4_readahead+0x47/0x50 read_pages+0x82/0x530 page_cache_ra_unbounded+0x199/0x2a0 do_page_cache_ra+0x47/0x70 page_cache_ra_order+0x242/0x400 ondemand_readahead+0x1e8/0x4b0 page_cache_sync_ra+0xf4/0x110 filemap_get_pages+0x131/0xb20 filemap_read+0xda/0x4b0 generic_file_read_iter+0x13a/0x250 ext4_file_read_iter+0x59/0x1d0 vfs_read+0x28f/0x460 ksys_read+0x73/0x160 __x64_sys_read+0x1e/0x30 do_syscall_64+0x35/0x80 entry_SYSCALL_64_after_hwframe+0x63/0xcd </TASK> ================================================================== In the above issue, ioctl invokes the swap_inode_boot_loader function to swap inode<5> and inode<12>. However, inode<5> contain incorrect imode and disordered extents, and i_nlink is set to 1. The extents check for inode in the ext4_iget function can be bypassed bacause 5 is EXT4_BOOT_LOADER_INO. While links_count is set to 1, the extents are not initialized in swap_inode_boot_loader. After the ioctl command is executed successfully, the extents are swapped to inode<12>, in this case, run the `cat` command to view inode<12>. And Bug_ON is triggered due to the incorrect extents. When the boot loader inode is not initialized, its imode can be one of the following: 1) the imode is a bad type, which is marked as bad_inode in ext4_iget and set to S_IFREG. 2) the imode is good type but not S_IFREG. 3) the imode is S_IFREG. The BUG_ON may be triggered by bypassing the check in cases 1 and 2. Therefore, when the boot loader inode is bad_inode or its imode is not S_IFREG, initialize the inode to avoid triggering the BUG. | ||||
| CVE-2025-68294 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: io_uring/net: ensure vectored buffer node import is tied to notification When support for vectored registered buffers was added, the import itself is using 'req' rather than the notification io_kiocb, sr->notif. For non-vectored imports, sr->notif is correctly used. This is important as the lifetime of the two may be different. Use the correct io_kiocb for the vectored buffer import. | ||||
| CVE-2023-54112 | 1 Linux | 1 Linux Kernel | 2026-04-15 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: kcm: Fix memory leak in error path of kcm_sendmsg() syzbot reported a memory leak like below: BUG: memory leak unreferenced object 0xffff88810b088c00 (size 240): comm "syz-executor186", pid 5012, jiffies 4294943306 (age 13.680s) hex dump (first 32 bytes): 00 89 08 0b 81 88 ff ff 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<ffffffff83e5d5ff>] __alloc_skb+0x1ef/0x230 net/core/skbuff.c:634 [<ffffffff84606e59>] alloc_skb include/linux/skbuff.h:1289 [inline] [<ffffffff84606e59>] kcm_sendmsg+0x269/0x1050 net/kcm/kcmsock.c:815 [<ffffffff83e479c6>] sock_sendmsg_nosec net/socket.c:725 [inline] [<ffffffff83e479c6>] sock_sendmsg+0x56/0xb0 net/socket.c:748 [<ffffffff83e47f55>] ____sys_sendmsg+0x365/0x470 net/socket.c:2494 [<ffffffff83e4c389>] ___sys_sendmsg+0xc9/0x130 net/socket.c:2548 [<ffffffff83e4c536>] __sys_sendmsg+0xa6/0x120 net/socket.c:2577 [<ffffffff84ad7bb8>] do_syscall_x64 arch/x86/entry/common.c:50 [inline] [<ffffffff84ad7bb8>] do_syscall_64+0x38/0xb0 arch/x86/entry/common.c:80 [<ffffffff84c0008b>] entry_SYSCALL_64_after_hwframe+0x63/0xcd In kcm_sendmsg(), kcm_tx_msg(head)->last_skb is used as a cursor to append newly allocated skbs to 'head'. If some bytes are copied, an error occurred, and jumped to out_error label, 'last_skb' is left unmodified. A later kcm_sendmsg() will use an obsoleted 'last_skb' reference, corrupting the 'head' frag_list and causing the leak. This patch fixes this issue by properly updating the last allocated skb in 'last_skb'. | ||||
| CVE-2023-54035 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_tables: fix underflow in chain reference counter Set element addition error path decrements reference counter on chains twice: once on element release and again via nft_data_release(). Then, d6b478666ffa ("netfilter: nf_tables: fix underflow in object reference counter") incorrectly fixed this by removing the stateful object reference count decrement. Restore the stateful object decrement as in b91d90368837 ("netfilter: nf_tables: fix leaking object reference count") and let nft_data_release() decrement the chain reference counter, so this is done only once. | ||||
| CVE-2022-50709 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: wifi: ath9k: avoid uninit memory read in ath9k_htc_rx_msg() syzbot is reporting uninit value at ath9k_htc_rx_msg() [1], for ioctl(USB_RAW_IOCTL_EP_WRITE) can call ath9k_hif_usb_rx_stream() with pkt_len = 0 but ath9k_hif_usb_rx_stream() uses __dev_alloc_skb(pkt_len + 32, GFP_ATOMIC) based on an assumption that pkt_len is valid. As a result, ath9k_hif_usb_rx_stream() allocates skb with uninitialized memory and ath9k_htc_rx_msg() is reading from uninitialized memory. Since bytes accessed by ath9k_htc_rx_msg() is not known until ath9k_htc_rx_msg() is called, it would be difficult to check minimal valid pkt_len at "if (pkt_len > 2 * MAX_RX_BUF_SIZE) {" line in ath9k_hif_usb_rx_stream(). We have two choices. One is to workaround by adding __GFP_ZERO so that ath9k_htc_rx_msg() sees 0 if pkt_len is invalid. The other is to let ath9k_htc_rx_msg() validate pkt_len before accessing. This patch chose the latter. Note that I'm not sure threshold condition is correct, for I can't find details on possible packet length used by this protocol. | ||||
| CVE-2022-50706 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: net/ieee802154: don't warn zero-sized raw_sendmsg() syzbot is hitting skb_assert_len() warning at __dev_queue_xmit() [1], for PF_IEEE802154 socket's zero-sized raw_sendmsg() request is hitting __dev_queue_xmit() with skb->len == 0. Since PF_IEEE802154 socket's zero-sized raw_sendmsg() request was able to return 0, don't call __dev_queue_xmit() if packet length is 0. ---------- #include <sys/socket.h> #include <netinet/in.h> int main(int argc, char *argv[]) { struct sockaddr_in addr = { .sin_family = AF_INET, .sin_addr.s_addr = htonl(INADDR_LOOPBACK) }; struct iovec iov = { }; struct msghdr hdr = { .msg_name = &addr, .msg_namelen = sizeof(addr), .msg_iov = &iov, .msg_iovlen = 1 }; sendmsg(socket(PF_IEEE802154, SOCK_RAW, 0), &hdr, 0); return 0; } ---------- Note that this might be a sign that commit fd1894224407c484 ("bpf: Don't redirect packets with invalid pkt_len") should be reverted, for skb->len == 0 was acceptable for at least PF_IEEE802154 socket. | ||||
| CVE-2023-54108 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: scsi: qla2xxx: Fix DMA-API call trace on NVMe LS requests The following message and call trace was seen with debug kernels: DMA-API: qla2xxx 0000:41:00.0: device driver failed to check map error [device address=0x00000002a3ff38d8] [size=1024 bytes] [mapped as single] WARNING: CPU: 0 PID: 2930 at kernel/dma/debug.c:1017 check_unmap+0xf42/0x1990 Call Trace: debug_dma_unmap_page+0xc9/0x100 qla_nvme_ls_unmap+0x141/0x210 [qla2xxx] Remove DMA mapping from the driver altogether, as it is already done by FC layer. This prevents the warning. | ||||
| CVE-2022-50705 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: io_uring/rw: defer fsnotify calls to task context We can't call these off the kiocb completion as that might be off soft/hard irq context. Defer the calls to when we process the task_work for this request. That avoids valid complaints like: stack backtrace: CPU: 1 PID: 0 Comm: swapper/1 Not tainted 6.0.0-rc6-syzkaller-00321-g105a36f3694e #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 08/26/2022 Call Trace: <IRQ> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106 print_usage_bug kernel/locking/lockdep.c:3961 [inline] valid_state kernel/locking/lockdep.c:3973 [inline] mark_lock_irq kernel/locking/lockdep.c:4176 [inline] mark_lock.part.0.cold+0x18/0xd8 kernel/locking/lockdep.c:4632 mark_lock kernel/locking/lockdep.c:4596 [inline] mark_usage kernel/locking/lockdep.c:4527 [inline] __lock_acquire+0x11d9/0x56d0 kernel/locking/lockdep.c:5007 lock_acquire kernel/locking/lockdep.c:5666 [inline] lock_acquire+0x1ab/0x570 kernel/locking/lockdep.c:5631 __fs_reclaim_acquire mm/page_alloc.c:4674 [inline] fs_reclaim_acquire+0x115/0x160 mm/page_alloc.c:4688 might_alloc include/linux/sched/mm.h:271 [inline] slab_pre_alloc_hook mm/slab.h:700 [inline] slab_alloc mm/slab.c:3278 [inline] __kmem_cache_alloc_lru mm/slab.c:3471 [inline] kmem_cache_alloc+0x39/0x520 mm/slab.c:3491 fanotify_alloc_fid_event fs/notify/fanotify/fanotify.c:580 [inline] fanotify_alloc_event fs/notify/fanotify/fanotify.c:813 [inline] fanotify_handle_event+0x1130/0x3f40 fs/notify/fanotify/fanotify.c:948 send_to_group fs/notify/fsnotify.c:360 [inline] fsnotify+0xafb/0x1680 fs/notify/fsnotify.c:570 __fsnotify_parent+0x62f/0xa60 fs/notify/fsnotify.c:230 fsnotify_parent include/linux/fsnotify.h:77 [inline] fsnotify_file include/linux/fsnotify.h:99 [inline] fsnotify_access include/linux/fsnotify.h:309 [inline] __io_complete_rw_common+0x485/0x720 io_uring/rw.c:195 io_complete_rw+0x1a/0x1f0 io_uring/rw.c:228 iomap_dio_complete_work fs/iomap/direct-io.c:144 [inline] iomap_dio_bio_end_io+0x438/0x5e0 fs/iomap/direct-io.c:178 bio_endio+0x5f9/0x780 block/bio.c:1564 req_bio_endio block/blk-mq.c:695 [inline] blk_update_request+0x3fc/0x1300 block/blk-mq.c:825 scsi_end_request+0x7a/0x9a0 drivers/scsi/scsi_lib.c:541 scsi_io_completion+0x173/0x1f70 drivers/scsi/scsi_lib.c:971 scsi_complete+0x122/0x3b0 drivers/scsi/scsi_lib.c:1438 blk_complete_reqs+0xad/0xe0 block/blk-mq.c:1022 __do_softirq+0x1d3/0x9c6 kernel/softirq.c:571 invoke_softirq kernel/softirq.c:445 [inline] __irq_exit_rcu+0x123/0x180 kernel/softirq.c:650 irq_exit_rcu+0x5/0x20 kernel/softirq.c:662 common_interrupt+0xa9/0xc0 arch/x86/kernel/irq.c:240 | ||||
| CVE-2022-50704 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: USB: gadget: Fix use-after-free during usb config switch In the process of switching USB config from rndis to other config, if the hardware does not support the ->pullup callback, or the hardware encounters a low probability fault, both of them may cause the ->pullup callback to fail, which will then cause a system panic (use after free). The gadget drivers sometimes need to be unloaded regardless of the hardware's behavior. Analysis as follows: ======================================================================= (1) write /config/usb_gadget/g1/UDC "none" gether_disconnect+0x2c/0x1f8 rndis_disable+0x4c/0x74 composite_disconnect+0x74/0xb0 configfs_composite_disconnect+0x60/0x7c usb_gadget_disconnect+0x70/0x124 usb_gadget_unregister_driver+0xc8/0x1d8 gadget_dev_desc_UDC_store+0xec/0x1e4 (2) rm /config/usb_gadget/g1/configs/b.1/f1 rndis_deregister+0x28/0x54 rndis_free+0x44/0x7c usb_put_function+0x14/0x1c config_usb_cfg_unlink+0xc4/0xe0 configfs_unlink+0x124/0x1c8 vfs_unlink+0x114/0x1dc (3) rmdir /config/usb_gadget/g1/functions/rndis.gs4 panic+0x1fc/0x3d0 do_page_fault+0xa8/0x46c do_mem_abort+0x3c/0xac el1_sync_handler+0x40/0x78 0xffffff801138f880 rndis_close+0x28/0x34 eth_stop+0x74/0x110 dev_close_many+0x48/0x194 rollback_registered_many+0x118/0x814 unregister_netdev+0x20/0x30 gether_cleanup+0x1c/0x38 rndis_attr_release+0xc/0x14 kref_put+0x74/0xb8 configfs_rmdir+0x314/0x374 If gadget->ops->pullup() return an error, function rndis_close() will be called, then it will causes a use-after-free problem. ======================================================================= | ||||
| CVE-2023-54099 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: fs: Protect reconfiguration of sb read-write from racing writes The reconfigure / remount code takes a lot of effort to protect filesystem's reconfiguration code from racing writes on remounting read-only. However during remounting read-only filesystem to read-write mode userspace writes can start immediately once we clear SB_RDONLY flag. This is inconvenient for example for ext4 because we need to do some writes to the filesystem (such as preparation of quota files) before we can take userspace writes so we are clearing SB_RDONLY flag before we are fully ready to accept userpace writes and syzbot has found a way to exploit this [1]. Also as far as I'm reading the code the filesystem remount code was protected from racing writes in the legacy mount path by the mount's MNT_READONLY flag so this is relatively new problem. It is actually fairly easy to protect remount read-write from racing writes using sb->s_readonly_remount flag so let's just do that instead of having to workaround these races in the filesystem code. [1] https://lore.kernel.org/all/[email protected]/T/ | ||||
| CVE-2023-54096 | 1 Linux | 1 Linux Kernel | 2026-04-15 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: soundwire: fix enumeration completion The soundwire subsystem uses two completion structures that allow drivers to wait for soundwire device to become enumerated on the bus and initialised by their drivers, respectively. The code implementing the signalling is currently broken as it does not signal all current and future waiters and also uses the wrong reinitialisation function, which can potentially lead to memory corruption if there are still waiters on the queue. Not signalling future waiters specifically breaks sound card probe deferrals as codec drivers can not tell that the soundwire device is already attached when being reprobed. Some codec runtime PM implementations suffer from similar problems as waiting for enumeration during resume can also timeout despite the device already having been enumerated. | ||||